VooPoo Drag Mod

Was: $64.99
Now: $32.49
(1 review) Write a Review
Maximum Purchase:
100 units

Probably no single mod in recent history has been met with as much excitement as the VooPoo Drag mod, and it's easy to see why. With unbelievably solid construction, a host of intelligent features, and more than enough power on tap, the VooPoo Drag is the mod to beat!

Just looking at the mod, you can tell it's well-built, but you really have to have it in hand to appreciate it. This is a solid, well-constructed mod, not something you're going to be pitching out in six months when the paint's worn off and the buttons keep sticking. This is a serious device, and the build quality reflects that. It's a looker, too: instead of looking flash, the VooPoo Drag plays it chill, with clean lines and smooth bevels. A class act.

But all the build quality and good looks in the world don't matter if the device is no bueno. Thankfully, that's not something you have to worry about with the VooPoo Drag. Making use of their amazing proproprietary GENE chip, the VooPoo Drag can do all the things you're used to from a DNA device, and more! It starts with one of the fastest firing times we've experienced: 0.025 seconds, or 25 milliseconds. That's literally faster than the blink of an eye, which is closer to 100 - 400 milliseconds. That's as close to instant as we need!

It's not just fast, either: it's also powerful. With two 18650 high-current vape batteries on board, the Drag can reach up to 157 watts, and will fire as low as 0.05 ohm - though not at the same time! To keep you correct, the VooPoo Drag has an innovative SUPER mode, which it automatically enters at 130 watts, to make certain you're using a coil with a low enough resistance to safely vape at that wattage - 0.1 to 0.3, in this case. Even better, its smart wattage mode will automatically adjust to whatever new coil or atomizer you've installed - no more accidentally burning coils, or anemic vapes, when you swap to a different resistance! A spring-loaded gold-plated brass 510 connector makes sure all that smart wattage gets where it belongs, too. Custom power curves deliver exactly the vaping experience you're looking for, every time.

Our fellow vapers in the temperature control crowd won't get left out in the cold, either: the TC support on this mod is excellent! It supports nickel, stainless steel, and titanium, and even a custom TCR value. It'll do a strong pre-heat "punch" of power to get your coil up to temp as fast as possible, and then adjusts power from there with unbelievably smooth TCR control. You can even set new TCR values for each material, as well as your own temp curves.

Perhaps best of all, the mod you buy only gets better and better, because the VooPoo Drag mod has updateable firmware. Simply connect your Drag to your PC with the included USB cable, download some easy-to-use software, and you can adjust features like the coefficient of all your materials in temperature control mode, your cutoff time, screen brightness, custom temperature curves and power curves, and even the appearance of nearly every screen on the Drag's beautiful OLED display!

And unlike some mods out there, that USB port isn't just for firmware updates: you can actually charge batteries in your VooPoo Drag. While we still recommend you use a high-quality vape battery charger, for maximum speed and safety, the VooPoo Drag will actually balance charge your 18650 cells, even if they're at different charge levels! The batteries stay where they belong with a magnetic battery door with clever anti-shorting appliques, just in case you haven't noticed a bad battery wrap.

MEL Zone:

With a 40 amp maximum current output, you're going to need a high-current vape battery. We recommend a 35 amp max battery like the Samsung 25R INR 18650 2500mAh 20A/35A Li-Ni-Mn f lat top battery to make the most out of a device like this one.

  • Maximum current output: 40 amps
  • Modes: Wattage, Voltage, Temp Control
  • Wattage range: 5 - 157 watts
  • Voltage range: 0.5 - 7.5 volts
  • Resistance range (Power modes): 0.05 - 3.0 ohm
  • Resistance range (TC mode): 0.05 - 1.5 ohm
  • TCR materials (TC mode): Ni, SS, Ti, custom TCR mode
  • Temperature range (TC mode): 200°F - 600°F
  • Protections: Battery reverse, time cutoff, over-temp, over-current, over-charge, over-discharge, short-circuit
What's in the Box:
  • (1) VooPoo Drag mod
  • (1) USB charging / firmware update cable
  • (1) User manual
  • (1) Warranty card

Learn more about this product at Vape University!

VooPoo Drag mod
VU254 (Lab) VooPoo Drag Mod

And here it is, the lab you've all been clamoring for: the amazing, the astonishing, the intelligent, the beautiful, the one and only VooPoo Drag box mod. With 157 watts on tap, shockingly low firing times, and all the smarts of today's top box mods, the VooPoo Drag is beloved by the vaping community, and for very good reason.

Videos Hide Videos Show Videos

1 Review Hide Reviews Show Reviews

  • 3

    Posted by Spaceman on 20th Oct 2018

    I gave this 3 stars due to the following, at best it’s Durable and heavy. One side looks like it was bedazzled and the buttons are a little loose and if not directly pressed they will not preform there intended function.

WARNING: This product contains nicotine.
Nicotine is an addictive chemical.

Due to state regulations, the legal age to purchase may vary. Please confirm your age using the chart below to continue.

18+ 19+ 21+
All US States Unless Specified Alabama, Alaska, Utah California, Hawaii, Iowa, Maine, New Jersey, Oregon